--- /dev/null
+#
+#
+# lispd example config file
+#
+#
+
+
+# General configuration
+# debug: Debug levels [0..3]
+# map-request-retries: Additional Map-Requests to send per map cache miss
+
+debug = 0
+map-request-retries = 2
+
+# RLOC Probing configuration
+# rloc-probe-interval: interval at which periodic RLOC probes are sent
+# (seconds). A value of 0 disables RLOC Probing
+# rloc-probe-retries: RLOC Probe retries before setting the locator with
+# status down. [0..5]
+# rloc-probe-retries-interval: interval at which RLOC probes retries are
+# sent (seconds) [1..#rloc-probe-interval]
+
+rloc-probing {
+ rloc-probe-interval = 0
+ rloc-probe-retries = 2
+ rloc-probe-retries-interval = 5
+}
+
+# NAT Traversal configuration.
+# nat_aware: check if the node is behind NAT
+# site_ID: 64 bits to identify the site which the node is connected to. In
+# hexadecimal
+# xTR_ID: 128 bits to identify the xTR inside the site. In hexadecimal
+# Limitation of version 0.3.3 when nat_aware is enabled:
+# - Only one interface is supported.
+# - Only one Map Server and one Map Resolver
+
+nat-traversal {
+ nat_aware = off
+ site_ID = 0000000000000001 #In doubt, keep the default value
+ xTR_ID = 00000000000000000000000000000001 #In doubt, keep the default value
+}
+
+# Encapsulated Map-Requests are sent to this map-resolver
+# You can define several map-resolvers. Encapsulated Map-Request messages will
+# be sent to only one.
+# address: IPv4 or IPv6 address of the map resolver
+map-resolver = {10.33.12.32}
+
+# Map-Registers are sent to this map-server
+# You can define several map-servers. Map-Register messages will be sent to all
+# of them.
+# address: IPv4 or IPv6 address of the map-server
+# key-type: Only 1 supported (HMAC-SHA-1-96)
+# key: password to authenticate with the map-server
+# proxy-reply [on/off]: Configure map-server to Map-Reply on behalf of the xTR
+
+map-server {
+ address = 192.0.2.1
+ key-type = 1
+ key = asdf
+ proxy-reply = on
+}
+
+# Packets addressed to non-LISP sites will be encapsulated to this Proxy-ETR
+# You can define several Proxy-ETR. Traffic will be balanced according to
+# priority and weight.
+# address: IPv4 or IPv6 address of the Proxy-ETR
+# priority [0-255]: Proxy-ETR with lower values are more preferable.
+# weight [0-255]: When priorities are the same for multiple Proxy-ETRs,
+# the Weight indicates how to balance unicast traffic between them.
+#proxy-etr {
+# address = 10.10.10.10
+# priority = 1
+# weight = 100
+#}
+
+# IPv4 / IPv6 EID of the node.
+# One database-mapping structure is defined for each interface with RLOCs
+# associated to this EID
+# eid-prefix: EID prefix (IPvX/mask) of the mapping
+# interface: interface containing the RLOCs associated to this mapping
+# priority_vX [0-255]: Priority for the IPvX RLOC of the interface. Locators
+# with lower values are more preferable. This is used for both incoming
+# policy announcements and outcoming traffic policy management. (A value
+# of -1 means that IPvX address of that interface is not used)
+# weight [0-255]: When priorities are the same for multiple RLOCs, the Weight
+# indicates how to balance unicast traffic between them.
+
+database-mapping {
+ eid-prefix = 2.2.2.2/32
+ interface = eth0
+ priority_v4 = 1 # Priority of IPv4 locator of the interface eth0 for this EID
+ weight_v4 = 100 # Weight of IPv4 locator of the interface eth0 for this EID
+ priority_v6 = 1 # Priority of IPv6 locator of the interface eth0 for this EID
+ weight_v6 = 100 # Weight of IPv6 locator of the interface eth0 for this EID
+}
+
+# List of PITRs to SMR on handover
+# address: IPv4 or IPv6 address of the Proxy-ITR
+#proxy-itrs = {
+# address,
+# [address ...]
+#}
+
+# Current LISP beta-network (lisp4.net/lisp6.net) PITR addresses
+# Uncomment the IPv4 or IPv6 list based on your current locators and
+# comment the previous 'proxy-itrs' section
+
+# LISP beta-network IPv4 PITRs
+#proxy-itrs = {
+# 69.31.31.98, # eqx-ash-pxtr
+# 149.20.48.60, # isc-pxtr
+# 198.6.255.37, # asp-pxtr
+# 173.36.193.25, # sjc-pxtr
+# 129.250.1.63, # ntt-amer-pxtr
+# 217.8.98.33, # intouch-pxtr-1
+# 217.8.98.35, # intouch-pxtr-2
+# 193.162.145.46, # tdc-pxtr
+# 158.38.1.92, # uninett-pxtr
+# 203.181.249.172, # apan-pxtr
+# 202.51.247.10 # sg-nus-pxtr
+#}
+
+# LISP beta-network IPv6 PITRs
+
+#proxy-itrs = {
+# 2001:590::451f:1f62, # eqx-ash-pxtr
+# 2001:4f8:3:d::60, # isc-pxtr
+# 2001:418:4:1:deaf:bebe::10d, # asp-pxtr
+# 2001:418:0:1000::613, # ntt-amer-pxtr
+# 2001:200:e000:17::17, # intouch-pxtr-1
+# 2001:67C:21B4:108::b, # intouch-pxtr-2
+# 2001:6c8:41:100:0:2:1:c, # tdc-pxtr
+# 2001:700:0:52E::4, # uninett-pxtr
+# 2001:67C:21B4:107::b # apan-pxtr
+#}
Code Review / lispflowmapping.git / blobdiff