#
#
#       lispd example config file
#
#


# General configuration
#	debug: Debug levels [0..3]
#	map-request-retries: Additional Map-Requests to send per map cache miss

debug                  = 0 
map-request-retries    = 2

# RLOC Probing configuration
#   rloc-probe-interval: interval at which periodic RLOC probes are sent
#     (seconds). A value of 0 disables RLOC Probing
#   rloc-probe-retries: RLOC Probe retries before setting the locator with
#     status down. [0..5]
#   rloc-probe-retries-interval: interval at which RLOC probes retries are
#     sent (seconds) [1..#rloc-probe-interval]

rloc-probing {
    rloc-probe-interval             = 0
    rloc-probe-retries              = 2
    rloc-probe-retries-interval     = 5
}

# NAT Traversal configuration. 
#   nat_aware: check if the node is behind NAT
#   site_ID: 64 bits to identify the site which the node is connected to. In
#     hexadecimal
#   xTR_ID: 128 bits to identify the xTR inside the site. In hexadecimal
# Limitation of version 0.3.3 when nat_aware is enabled: 
#   - Only one interface is supported.
#   - Only one Map Server and one Map Resolver

nat-traversal {
    nat_aware   = off
    site_ID     = 0000000000000001                  #In doubt, keep the default value
    xTR_ID      = 00000000000000000000000000000001  #In doubt, keep the default value
}

# Encapsulated Map-Requests are sent to this map-resolver
# You can define several map-resolvers. Encapsulated Map-Request messages will
# be sent to only one.
#   address: IPv4 or IPv6 address of the map resolver  
map-resolver        = {10.33.12.32}

# Map-Registers are sent to this map-server
# You can define several map-servers. Map-Register messages will be sent to all
# of them.
#   address: IPv4 or IPv6 address of the map-server
#   key-type: Only 1 supported (HMAC-SHA-1-96)
#   key: password to authenticate with the map-server
#   proxy-reply [on/off]: Configure map-server to Map-Reply on behalf of the xTR

map-server {
        address	    = 192.0.2.1
        key-type    = 1
        key	    = asdf
	proxy-reply = on
}

# Packets addressed to non-LISP sites will be encapsulated to this Proxy-ETR
# You can define several Proxy-ETR. Traffic will be balanced according to
# priority and weight.
#   address: IPv4 or IPv6 address of the Proxy-ETR
#   priority [0-255]: Proxy-ETR with lower values are more preferable.
#   weight [0-255]: When priorities are the same for multiple Proxy-ETRs,
#     the Weight indicates how to balance unicast traffic between them.
#proxy-etr {
#	address     = 10.10.10.10
#	priority    = 1
#	weight      = 100
#}

# IPv4 / IPv6 EID of the node.
# One database-mapping structure is defined for each interface with RLOCs
# associated to this EID
#   eid-prefix: EID prefix (IPvX/mask) of the mapping 
#   interface: interface containing the RLOCs associated to this mapping 
#   priority_vX [0-255]: Priority for the IPvX RLOC of the interface. Locators
#     with lower values are more preferable. This is used for both incoming
#     policy announcements and outcoming traffic policy management. (A value
#     of -1  means that IPvX address of that interface is not used)
#   weight [0-255]: When priorities are the same for multiple RLOCs, the Weight
#     indicates how to balance unicast traffic between them.

database-mapping {
         eid-prefix 	= 2.2.2.2/32
         interface  	= eth0
         priority_v4	= 1				# Priority of IPv4 locator of the interface eth0 for this EID
         weight_v4     	= 100				# Weight of IPv4 locator of the interface eth0 for this EID
         priority_v6	= 1				# Priority of IPv6 locator of the interface eth0 for this EID
         weight_v6     	= 100				# Weight of IPv6 locator of the interface eth0 for this EID
}

# List of PITRs to SMR on handover
#   address: IPv4 or IPv6 address of the Proxy-ITR
#proxy-itrs = {
#	address,
#	[address ...]
#}

# Current LISP beta-network (lisp4.net/lisp6.net) PITR addresses
# Uncomment the IPv4 or IPv6 list based on your current locators and
# comment the previous 'proxy-itrs' section

# LISP beta-network IPv4 PITRs
#proxy-itrs = {
#	69.31.31.98,		# eqx-ash-pxtr
#	149.20.48.60,		# isc-pxtr
#	198.6.255.37,		# asp-pxtr
#	173.36.193.25,		# sjc-pxtr
#	129.250.1.63,		# ntt-amer-pxtr
#	217.8.98.33,		# intouch-pxtr-1
#	217.8.98.35,		# intouch-pxtr-2
#	193.162.145.46,		# tdc-pxtr
#	158.38.1.92,		# uninett-pxtr
#	203.181.249.172,	# apan-pxtr
#	202.51.247.10		# sg-nus-pxtr
#}

# LISP beta-network IPv6 PITRs 

#proxy-itrs = {
#	2001:590::451f:1f62,		# eqx-ash-pxtr
#	2001:4f8:3:d::60,		# isc-pxtr
#	2001:418:4:1:deaf:bebe::10d, 	# asp-pxtr
#	2001:418:0:1000::613, 		# ntt-amer-pxtr
#	2001:200:e000:17::17,   	# intouch-pxtr-1
#	2001:67C:21B4:108::b,    	# intouch-pxtr-2
#	2001:6c8:41:100:0:2:1:c, 	# tdc-pxtr
#	2001:700:0:52E::4, 		# uninett-pxtr
#	2001:67C:21B4:107::b    	# apan-pxtr
#}